美国网件(NETGEAR) - 技术支持

SRX5308 Version 4.2.1-2

发布日期：2012年12月27日

新特性

从3.x.x或者之前的固件版本升级到v4.2.0-22，必须恢复到出厂设置。而且不能导入之前版本的配置备份文件。

新特性

支持动态密码

已知问题

IGMP snooping functionality is not working.
Only display one RADVD prefix delegation to advertise.
Bandwidth functionality is not working over VPN GW-GW tunnel.
No IPV6 IPSec throughput when use TCP/1518 frame packet.
[IPv6]Unable to establish the IPV6 manual tunnel with traffic selector as ANY/ANY.
Not able to run multicast traffic over l2tp.
Not able to do netbios over l2tp tunnel.
[IPv6]Displaying the message as address not found instead of ,Blocked from this Browser, for IPv6 policy ,Deny Login From Defined Browsers,.
UDP traffic with size more than 1452 is not running over ipv6 sslvpn tunnel.
Unable to configure IPSec VPN policies using WAN ip aliases.
Logs are not coming in view logs page for added scheduled based ipv6 firewall rule.
Unable to send the logs over vpn tunnel.
Traffic is not following wan upload or down load(higher one of them )speeds if the upload and down load speeds having large difference.
[CLI]Multiple firewall rules are getting added when we give "save" command for multiple times in CLI.
[CLI]Device not showing the connection status of the IPv4 and IPV6 ipsec policy in cli until we open the connection status page in GUI.
[CLI]Firewall logs table is not updating properly for enabling and disabling logs through cli.
Sync time failed from NTP server over VPN tunnel.
When establish sslvpn ipv6 tunnel,thensslvpn ipv4 tunnel also successfully established.
[IPv6] static route which interface is WAN can,t be recorded IPv6 route table on GUI only.
Do not record system log about "change of time by NTP".
Can not manage DUT from lan host when lan traffic reach the limit.
Start Date/Time is wrong in Traffic Meter page and always using GMT zone.
The wan upload/download connection speed are displayed incorrectly on detailed status page.
Log always does not work for DMZ-WAN inbound block rules under NAT mode.
No bandwidth limit log in view logs.
[CLI] firewall rules for wan-lan does not have single ip selection for wan destination.
[CLI] System snmp trap conifgure command does not have option to select snmp v1, v2 or v3.
[CLI] Show commands do not work for system snmp trap, system time setup, sysinfo, system logs.
[CLI] Show commands do not work for vpnipsec and sslvpn logs.
[CLI] Show wan ipv4 setup does not work if no secondary DNS server configured.
L2TP/PPTP tunnel only could be established through the primary address.
Only display one RADVD prefix delegation to advertise.
[IPv6]Customized VLAN do not support IPv6.
FTP client passive mode cannot open data connection while inbound rule using "translate to port number".
[IPv6]QoS priority is not supported for IPv6.
Wan traffic meter show the wrong statistics data in load balancing or auto rollover mode.

升级办法：

点击下面的按钮下载升级文件到你的电脑上。

26.4M
通过浏览器登录到管理界面，点击 Administration>Settings Backup & Upgrade 管理菜单，在 Router upgrade 选项中点击“浏览”，选中刚才下载的升级文件。
点击Upgrade。
等待文件传输完毕，路由器将会重新启动，等待直到路由器的 TEST 指示灯熄灭之后，路由器的升级完成。
通过路由器前面面板的Facotry Default 按扭或管理界面 Administration>Settings Backup & Upgrade 的 Default 按扭恢复出厂设置值。