发布日期：2007年8月23日

新特性/增强功能/问题修复：

1. Add support for new POE switch FSM7328PS
2. Add “save” command allows saving running config into flash with a single command
3. Add “show running config interface” shows the configuration per interface
4. Configure certain IGMP snooping using Web GUI, the switch might crash
5. FSM7300S: Unable to bind MAC ACL list to the interface
6. FSM7300S: IP ACL does not work properly
7. FSM7300S: “show interface” command right after the switch is rebooted will cause the crash
8. SNMP v3 packet might cause the switch to crash
9. GSM7312 crashes when the client address is blank in SNMP Community config
10. SNTP Server Configuration pageAddress Type" field is mistakenly configured as "DNS", device fails to update the time
11. VLAN GUI config page is error in not highlighting the member
12. GSM7328FS: fiber SFP link not up after module remove and reinsert
13. GSM7300S/FS - master unit reboot intermittently
14. GSM7300S/FS: eventlog shows corrupted entry
15. FSM7326P: IGMP Snooping: ,ip igmpsnooping unknown-multicast filter, does not take effect
16. When device originates ARP request for the target in secondary network with Sender IP Address as Primary Interface
17. When using default IP address in network interface, copy command failed
18. MFDB table do not get updated when client send IGMP leave
19. The speed for the port for 1G SFP module is shown to be unknown when specific port is selected on port configuration web page
20. Fails to accept host name begins with digit (0-9).
21. GUI : garbage character appear when configuring policy map
22. Dot1x : access fail after changing port-control from auto to force-authorized
23. Port security may impede MAC address learning
24. GSM7328S crashed when combo port mode is set to speed of 100Mbps
25. GSM7328S could not set 100Mbps half-duplex for gigabit port
26. GSM7328S port status stayed down when both sides port mode are set at 1000Mbps full-duplex.

已知的限制和局限性：

1. GSM7212: Jumbo frame does not work
2. Switch will not forward IS-IS packets

升级过程和注意事项

注意：

• 6.2.0.14支持之前版本的配置。如果从该版本转换到5.x版本，配置将会丢失。如果当前是5.x版本，请保存当前的配置以便转到5.x版本的时候使用。所有6.x版本之间的配置可以互用。

1. 点击以下按钮下载 firmware 文件。
   
   12.7MB
   
   该下载包含2个 firmware版本-6.2.0.6和6.2.0.14
   如果从6.1或更早以前的版本更新GSM7300系列（GSM7328S，GSM7328FS，GSM7352S），请按下列步骤进行操作：
   • 升级交换机到下载包里的6.2.0.6版本。
   • 升级完成后用6.2.0.6版本运行交换机。
   • 现在再升级到下载包里的6.2.0.14版本。
     
     
2. 参考升级说明及注意事项进行升级。

可以输入任何问题，一个产品型号或者一个功能进行查询

客服电话

电话销售热线：      服务时间（法定节假日除外）： 家庭产品：周一至周六 9:00-18:00 商用产品：周一至周五 9:00-18:00

客服邮箱